Introduction
These rubber-gelatin lifters are especially developed for the lifting of fingerprints, footprints, dustmarks and micro traces. The thick, non-aggressive, low-adhesive gelatin layer permits the lifting of traces from almost every surface, including porous materials, such as paper or cardboard. Lifted prints can be collected for photography or closer examination. The lifters consist of three layers: the Carrier, the Adhesive and the Cover Sheet (figure one). There are three kinds of lifters: Black lifters, White lifters and Transparent lifters.

The black and the white lifters have a carrier of linen rubber. The transparent lifters have a clear polyester film as a carrier. All lifters are protected by a transparent polyester Film. Black and white lifters can easily be marked since the white linen rubber backing can be written on. The transparent lifters have non-sticking paper edges for marking and easy lifting of the cover sheet. The lifters can easily be cut with scissors to fit a particular job. Do not remove the cover sheet before cutting (Figure two).

Fingerprints
Lifted prints or marks can easily be photographed after removal of the cover sheet. When the prints have been photographed the cover sheet can be replaced (after careful cleaning to remove any possible contamination).

Powdered Fingerprints can always be lifted with rubber-gelatin lifters. Which kind of lifter should be used depends on the color of the powder and personal preference. With silver or gray powder, for instance, the black lifters can be used to improve contrast. It should be remembered that with white and black lifters a negative image of the fingerprint is obtained.

Photography is then necessary to obtain the positive image. With the transparent lifters, a positive image can be obtained directly by photographing them through the transparent backing. To lift a powdered print, cut a section large enough to cover the area. It is recommended to cut off or notch a small corner of the lifter (Figure three).

There are two reasons for this. The first reason is that after lifting, the notched cover sheet can easily be replaced exactly over the lifter. The second reason is that if the lifter is always used in the same way, for instance with the notched edge on the right hand top side while lifting, the orientation of the lifted print can always be reconstructed. Before lifting the print, the cover sheet has to be removed (Figure four) and put aside, upside down (to avoid contamination).

The safest and only recommended method for placing the lifter on the print is described in the next paragraph. Adhere an edge of the lifter next to the developed print. The upwardly slanted lifter is now carefully smoothed down, while rubbing with a thumb, so that no air bubbles are locked in (Figure five). After that, the lifter is smoothed over the whole surface. Subsequently, the lifter is picked up, beginning at one of the corners. Then put the lifter (gelatin layer up) on a flat horizontal surface to replace the cover sheet. For small prints this can be done analogous to the lifting procedure described above (Figure six). For larger prints (e.g., palm prints), a roller is very convenient (Figure seven). Trapping of air bubbles will result in the creation of shallow craters, which will not destroy the print, but may cause problems in photography. Lifted dusted prints will fade, and ultimately disappear in time. Fading will be noticeable after days or weeks, depending on the storage temperature (the lower the better). Prints developed with silver powders, on the other hand, are known to have been stored for several years without apparent fading. It is recommended though, to photograph prints as soon as possible.

Splicing a Print
In case too much powder has been used, and the Fingerprint ridge detail is filled in, improvement of the print may be possible by the so-called Splicing of the print In splicing, two pieces of the same size lifter are used. First, the print is lifted as described above, and the cover sheet replaced. (Replacement of the cover sheet is essential, as will be clear in the following description.) Then the cover sheet is removed again. Due to the presence of excess powder, a copy of the print will be visible on the cover sheet. This copy can be transferred to the second piece of lifter by switching the covers. That is, the cover sheet of lifter #1 is put on lifter #2, and vice versa. In many cases this procedure will also improve the print on lifter #1 as well. Splicing can be advantageous in another way. When dirt or dust from the surface has been picked up during lifting, the dirt will remain on lifter #1 and the print is transferred to clean lifter #2, so that an undisturbed print is obtained. Note: There seems to be a controversy about the ethics of this technique. Some experts, therefore, prefer to use double lifting of a print (described in the next paragraph) when splicing seems advantageous.

Double Lifting
Often, a latent print can be lifted twice with only one application of latent print powder. The second lift will, in many cases be much clearer, but with less contrast. Another possibility is lifting for a second time after an additional application of powder. Of course, no rules can be given for these techniques, as much depends on experience. It is recommended though to try it for latent Fingerprints on aluminum.

Improvement of Older Prints
Fingerprints on objects which have been standing in sunlight or outside for longer periods are difficult to visualize. Because all of the water is evaporated from the print, hardly any powder adheres to it. By attaching a piece of lifter to it for some minutes, the print can be rehumidified. Subsequently, the print can be dusted in the usual way and lifted with a fresh piece of lifter. Before performing this technique, be sure that the objects have cooled.

Footwear Impression in Dust
In dust, the sole of a shoe acts like a stamper, leaving an invisible or hardly visible print. Shoeprints can be lifted from all smooth and hard surfaces, such as floor coverings, painted wood, paper, tabletops, etc., with rubber-gelatin lifters. For lifting shoeprints in dust, the large black lifters are commonly used. Dustprints not visible to the naked eye can be searched for in two ways. Either the prints are First discovered with the aid of a Floodlight, Forensic Light Source or Flashlight, and then lifted, or the whole area where prints are suspected is covered with lifters. If the whole area is covered with lifters, reconstruction of the pattern is aided by drawing stripes over the seams of the lifters and numbering them. It may be advantageous to leave the lifters on the surface for some minutes, to fully adhere to the dustprint. Even if the shoeprints did not show up on lighting the surface and were not visible upon lifting, they may show up under oblique lighting of the lifter surface in a dark room (after removing the cover sheet). Lifters with no apparent prints in normal light, may now show a highly detailed image. After photography, the cover sheet can be replaced after careful cleaning. For replacement of the cover sheet on these large lifters, without trapping air bubbles, a large roller is very convenient (Figure seven). Shoeprints made visible with Fingerprint powder can also be lifted with rubber-gelatin lifters. WARNING: Avoid contamination of the lifters after having removed the cover sheet. It is recommended to wear dust-free clothing during handling and photographing of the lifters.

Longevity of Latent Shoeprints
Lifted shoeprints (dustmarks) may slowly fade in time. For very weak prints this may be noticeable after storing for a few days. This will depend on temperature. The lower the temperature, the slower the fading. This, however, should not be a concern, since lifted shoeprints can easily be photographed after removing the cover sheet. Oblique lighting will show details not visible before photography. So far, no materials are known to us that faded on the lifter surface before satisfying photographs had been taken. When shoeprints contain very coarse material, e.g., sand, problems is expected in replacing the cover sheet. Around the coarse particles, small air bubbles will be present. When too many are present, the cover sheet will not sufficiently be adhered to the lifter. Several measures can be taken to avoid these problems. First of all, it is recommended to photograph the shoeprint before lifting. Second, the lifted print can be photographed at the crime scene before the cover sheet is replaced. Third, instead of replacing the cover sheet, the lifter can be put in a clean box (e.g., a photo-paper box) and taped to the bottom. Fourth, the cover sheet can be secured to the lifter with staples or adhesive tape, to prevent movement in which the coarse particles might destroy characteristic details.

Paint Traces
When paint left on a vehicle by a hit-and-run accident has to be collected for examination, the white lifters can be used. After removing the cover sheet, one edge of the lifter is attached to the surface of the vehicle, directly under the spot with the paint to be removed. Then, the paint is scraped off carefully with a scalpel. The removed material will fall in the gap between the lifter and the surface of the vehicle, or on the lifter itself. When enough material has been removed, the lifter is pressed to the surface of the vehicle. This way, all loose particles will be picked up by the lifter. The lifter can be removed and the cover sheet replaced. If necessary, the cover can be secured with staples or adhesive tape.

Sampling of Micro Traces
Due to the non-aggressive nature of the lifter, micro traces and hairs can be collected without fear of damaging the sampled material. When it is necessary to remove micro traces from the lifter, the low tack enables removal by using a scalpel or pair of tweezers. Collection of hair is done with white lifters. If an area is to be searched for micro traces, it is recommended to divide the area in squares (e.g., 20 x 20 cm or about 8 x 8 in.) and to use a fresh piece of lifter for each square. The size of the lifter is actually dictated by the amount of contamination in the area to be investigated, since sampling of dirt or large amounts of micro traces will result in quick loss of tack. A piece of 8 x 8 cm (about 3 x 3 in.) usually suffices.